Belt Scrapers - Revision history

Admin at 07:02, 18 February 2013

2013-02-18T07:02:33Z

← Older revision		Revision as of 01:02, 18 February 2013
Line 42:		Line 42:

	==Function, Cleaning and Care==		==Function, Cleaning and Care==
	*Primary Belt Cleaners:The function of the primary cleaner is to "scalp" the belt of the coarse carry back materials which would otherwise overload the secondary and tertiary cleaners. In terms of volume, the primary cleaner is responsible for the removal of up to 75% of the total carry back and is an essential part of the system. It has the added advantage of placing the carry back directly into the flow of material. The course materials do not cause a problem of carry back. This is normally because of the fine and sticky particles in the mix of material. These fine and sticky particles are removed by the secondary and [[Tertiary Cleaners]].		*Primary Belt Cleaners:The function of the primary cleaner is to "scalp" the belt of the coarse carry back materials which would otherwise overload the secondary and tertiary cleaners. In terms of volume, the primary cleaner is responsible for the removal of up to 75% of the total carry back and is an essential part of the system. It has the added advantage of placing the carry back directly into the flow of material. The course materials do not cause a problem of carry back. This is normally because of the fine and sticky particles in the mix of material. These fine and sticky particles are removed by the secondary and [[Tertiary Belt Cleaners]].
	*Secondary Belt Cleaners: The function of the secondary cleaner is to remove fine and sticky materials from the belt after the primary cleaner has removed the course carry back. In terms of volume removed, the secondary cleaner does not appear to be as effective as the primary cleaner. However, this does not ring true when looking at the mess around a conveyor or the build-up on return rollers. It is the fine and sticky material that is responsible for the mess as it is particularly hard to remove. In many cases, it is necessary to apply water to the belt in front of the secondary cleaner to achieve the required result.		*Secondary Belt Cleaners: The function of the secondary cleaner is to remove fine and sticky materials from the belt after the primary cleaner has removed the course carry back. In terms of volume removed, the secondary cleaner does not appear to be as effective as the primary cleaner. However, this does not ring true when looking at the mess around a conveyor or the build-up on return rollers. It is the fine and sticky material that is responsible for the mess as it is particularly hard to remove. In many cases, it is necessary to apply water to the belt in front of the secondary cleaner to achieve the required result.

Admin at 12:15, 17 February 2013

2013-02-17T12:15:08Z

← Older revision		Revision as of 06:15, 17 February 2013
Line 11:		Line 11:
	==Types of Belt Scrapers ==		==Types of Belt Scrapers ==
	===Primary Belt Cleaners or Precleaners===		===Primary Belt Cleaners or Precleaners===
	[[Primary Belt Cleaners]] or [[~~PreCleaners~~]] are an essential part of any conveyor system. Belt cleaners help remove bulk material product carry back and prevent it from falling off at various points of the conveyor along the return side of the belt causing various housekeeping and conveyor belt maintenance problems. These are installed at a positive angle, these primary belt cleaners would be mounted directly against the head pulley below the normal trajectory path of the material.		[[Primary Belt Cleaners]] or [[Precleaners]] are an essential part of any conveyor system. Belt cleaners help remove bulk material product carry back and prevent it from falling off at various points of the conveyor along the return side of the belt causing various housekeeping and conveyor belt maintenance problems. These are installed at a positive angle, these primary belt cleaners would be mounted directly against the head pulley below the normal trajectory path of the material.
	* Mounted on the head pulley.		* Mounted on the head pulley.
	* Mounted below the material flow.		* Mounted below the material flow.

Admin at 08:36, 17 February 2013

2013-02-17T08:36:40Z

← Older revision		Revision as of 02:36, 17 February 2013
Line 1:		Line 1:
	[[Category:Cleaning]]{{Knoppen}}		[[Category:Cleaning]]{{Knoppen}}
	~~<noinclude><!------------------------------------------------~~
	* READ THIS FIRST
	* Only edit this page if you can improve the content.
	* Improper use of this page will lead to permanent banning.
	* Please do not edit the sponsored link on the top right corner.
	* Please start editing this page after the /noinclude
	* -------------------------------------------------></noinclude>
	[[Image:Belt-cleaner.jpg\|thumb\|200px\|Belt Scraper]]		[[Image:Belt-cleaner.jpg\|thumb\|200px\|Belt Scraper]]
	[[Image:Secondary-belt-cleaner.jpg\|thumb\|200px\|Secondary Belt Scraper]]		[[Image:Secondary-belt-cleaner.jpg\|thumb\|200px\|Secondary Belt Scraper]]

Admin at 05:34, 27 July 2012

2012-07-27T05:34:04Z

← Older revision		Revision as of 23:34, 26 July 2012
Line 72:		Line 72:

	==Impact beds==		==Impact beds==
	Extending belt life, reducing wear on ~~idlers~~ and reducing downtime is achieved by using impact beds, which support the conveyor belt and cushion it against the shock impact of heavy loads. ABS custom-makes and supplies impact beds and skirting for all high impact areas on transfer chutes to suit any site application.		Extending belt life, reducing wear on [[Idlers]] and reducing downtime is achieved by using impact beds, which support the conveyor belt and cushion it against the shock impact of heavy loads. ABS custom-makes and supplies impact beds and skirting for all high impact areas on transfer chutes to suit any site application.


	== Video ==		== Video ==
	<youtube>maMM4DTfFDM</youtube>		<youtube>maMM4DTfFDM</youtube>

Admin at 05:33, 27 July 2012

2012-07-27T05:33:34Z

← Older revision		Revision as of 23:33, 26 July 2012
Line 17:		Line 17:

	==Types of Belt Scrapers ==		==Types of Belt Scrapers ==
	===Primary ~~belt cleaners~~ or Precleaners===		===Primary Belt Cleaners or Precleaners===
	Primary ~~belt cleaners~~ or ~~Pre-Cleaners~~ are an essential part of any conveyor system. Belt cleaners help remove bulk material product carry back and prevent it from falling off at various points of the conveyor along the return side of the belt causing various housekeeping and conveyor belt maintenance problems. These are installed at a positive angle, these primary belt cleaners would be mounted directly against the head pulley below the normal trajectory path of the material.		[[Primary Belt Cleaners]] or [[PreCleaners]] are an essential part of any conveyor system. Belt cleaners help remove bulk material product carry back and prevent it from falling off at various points of the conveyor along the return side of the belt causing various housekeeping and conveyor belt maintenance problems. These are installed at a positive angle, these primary belt cleaners would be mounted directly against the head pulley below the normal trajectory path of the material.
	* Mounted on the head pulley.		* Mounted on the head pulley.
	* Mounted below the material flow.		* Mounted below the material flow.
Line 34:		Line 34:

	===Secondary Belt Cleaners===		===Secondary Belt Cleaners===
	Secondary Belt Cleaners move bulk material product build-up and prevent it from falling off at different points of the conveyor. Points along the return side of the belt can cause various conveyor belt maintenance problems due to carry-back. Installed after the point where the belt leaves the head (discharge) pulley and or anywhere on the return side of the belt where it can be cleaned and maintained effectively.		[[Secondary Belt Cleaners]] move bulk material product build-up and prevent it from falling off at different points of the conveyor. Points along the return side of the belt can cause various conveyor belt maintenance problems due to carry-back. Installed after the point where the belt leaves the head (discharge) pulley and or anywhere on the return side of the belt where it can be cleaned and maintained effectively.
	* Special secondaries may allow for mounting under the head pulley.		* Special secondaries may allow for mounting under the head pulley.
	* Blade width is always the belt width or wider.		* Blade width is always the belt width or wider.
Line 49:		Line 49:

	==Function, Cleaning and Care==		==Function, Cleaning and Care==
	*Primary Belt Cleaners:The function of the primary cleaner is to "scalp" the belt of the coarse carry back materials which would otherwise overload the secondary and tertiary cleaners. In terms of volume, the primary cleaner is responsible for the removal of up to 75% of the total carry back and is an essential part of the system. It has the added advantage of placing the carry back directly into the flow of material. The course materials do not cause a problem of carry back. This is normally because of the fine and sticky particles in the mix of material. These fine and sticky particles are removed by the secondary and ~~tertiary cleaners~~.		*Primary Belt Cleaners:The function of the primary cleaner is to "scalp" the belt of the coarse carry back materials which would otherwise overload the secondary and tertiary cleaners. In terms of volume, the primary cleaner is responsible for the removal of up to 75% of the total carry back and is an essential part of the system. It has the added advantage of placing the carry back directly into the flow of material. The course materials do not cause a problem of carry back. This is normally because of the fine and sticky particles in the mix of material. These fine and sticky particles are removed by the secondary and [[Tertiary Cleaners]].
	*Secondary Belt Cleaners: The function of the secondary cleaner is to remove fine and sticky materials from the belt after the primary cleaner has removed the course carry back. In terms of volume removed, the secondary cleaner does not appear to be as effective as the primary cleaner. However, this does not ring true when looking at the mess around a conveyor or the build-up on return rollers. It is the fine and sticky material that is responsible for the mess as it is particularly hard to remove. In many cases, it is necessary to apply water to the belt in front of the secondary cleaner to achieve the required result.		*Secondary Belt Cleaners: The function of the secondary cleaner is to remove fine and sticky materials from the belt after the primary cleaner has removed the course carry back. In terms of volume removed, the secondary cleaner does not appear to be as effective as the primary cleaner. However, this does not ring true when looking at the mess around a conveyor or the build-up on return rollers. It is the fine and sticky material that is responsible for the mess as it is particularly hard to remove. In many cases, it is necessary to apply water to the belt in front of the secondary cleaner to achieve the required result.

Admin at 00:22, 12 July 2012

2012-07-12T00:22:01Z

← Older revision		Revision as of 18:22, 11 July 2012
Line 7:		Line 7:
	* Please start editing this page after the /noinclude		* Please start editing this page after the /noinclude
	* -------------------------------------------------></noinclude>		* -------------------------------------------------></noinclude>
	[[Image:Belt-cleaner.jpg\|thumb\|200px\|Belt ~~Cleaner~~]]		[[Image:Belt-cleaner.jpg\|thumb\|200px\|Belt Scraper]]
			[[Image:Secondary-belt-cleaner.jpg\|thumb\|200px\|Secondary Belt Scraper]]
	[[Image:Secondary-belt-cleaner.jpg\|thumb\|200px\|Secondary Belt ~~Cleaner~~]]
	'''Belt Scrapers''' or [[Belt Cleaners]] are used to clean [[Conveyor Belts]]. Belt Scrapers are exceptionally simple in design, its operations can certainly save thousands of man-hours, reduce injury hazard and prevent downtime from damaged components. These are used in bulk material handling belt conveyors to avoid material carry back and reduce spillage. Clean belts help prevent material build-up on snub pulley & return idlers, thereby reducing maintenance and downtime.		'''Belt Scrapers''' or [[Belt Cleaners]] are used to clean [[Conveyor Belts]]. Belt Scrapers are exceptionally simple in design, its operations can certainly save thousands of man-hours, reduce injury hazard and prevent downtime from damaged components. These are used in bulk material handling belt conveyors to avoid material carry back and reduce spillage. Clean belts help prevent material build-up on snub pulley & return idlers, thereby reducing maintenance and downtime.

Admin at 00:17, 12 July 2012

2012-07-12T00:17:29Z

← Older revision		Revision as of 18:17, 11 July 2012
Line 15:		Line 15:
	==Operation and Performance ==		==Operation and Performance ==
	The function of an efficient belt cleaning system is to remove the fugitive material which remains on the return strand of the belt and to assist in spillage control by returning that material to the main material flow within the confines of the discharge chute.		The function of an efficient belt cleaning system is to remove the fugitive material which remains on the return strand of the belt and to assist in spillage control by returning that material to the main material flow within the confines of the discharge chute.


	==Types of Belt Scrapers ==		==Types of Belt Scrapers ==

Admin at 00:16, 12 July 2012

2012-07-12T00:16:58Z

Show changes

Natgeo at 05:28, 11 July 2012

2012-07-11T05:28:33Z

@@ Line 7: / Line 7: @@
 * Please start editing this page after the /noinclude
 * -------------------------------------------------></noinclude>
-This page is still empty. If you know something about this product, please share your knowledge with others.

Natgeo at 11:42, 6 July 2012

2012-07-06T11:42:01Z

@@ Line 7: / Line 7: @@
 * Please start editing this page after the /noinclude
 * -------------------------------------------------></noinclude>
-'''Belt Scrapers''' are exceptionally simple in design, its operations can certainly save thousands of man-hours, reduce injury hazard and prevent downtime from damaged components. These are used in bulk material handling belt conveyors to avoid material carry back and reduce spillage. Clean belts help prevent material build-up on snub pulley & return idlers, thereby reducing maintenance and downtime. The function of an efficient belt cleaning system is to remove the fugitive material which remains on the return strand of the belt and to assist in spillage control by returning that material to the main material flow within the confines of the discharge chute.
+This page is still empty. If you know something about this product, please share your knowledge with others.