Bends - Revision history

Admin at 12:42, 12 March 2014

2014-03-12T12:42:14Z

← Older revision		Revision as of 06:42, 12 March 2014
Line 1:		Line 1:
	[[Category:Piping]]{{Knoppen}}		[[Category:Piping]]{{Knoppen}}
	~~<noinclude><!------------------------------------------------~~
	* READ THIS FIRST
	* Only edit this page if you can improve the content.
	* Improper use of this page will lead to permanent banning.
	* Please do not edit the sponsored link on the top right corner.
	* Please start editing this page after the /noinclude
	* -------------------------------------------------></noinclude>
	[[File:Bends.jpg\|thumb\|right\|Bends]]		[[File:Bends.jpg\|thumb\|right\|Bends]]
	'''Bend''' is a manufacturing process that produces a V-shape, U-shape, or channel shape along a straight axis in ductile materials, most commonly sheet metal.Commonly used equipment include		'''Bend''' is a manufacturing process that produces a V-shape, U-shape, or channel shape along a straight axis in ductile materials, most commonly sheet metal.Commonly used equipment include
	box and pan brakes, brake presses, and other specialized machine presses. Typical products that are made like this are boxes such as electrical enclosures and rectangular ductwork.		box and pan brakes, brake presses, and other specialized machine presses. Typical products that are made like this are boxes such as electrical enclosures and rectangular ductwork.


	==Process==		==Process==
	In press brake forming, a work piece is positioned over the die block and the die block presses the sheet to form a shape.Usually bend has to overcome both tensile stresses and compressive stresses. When bend is done, the residual stresses cause the material to spring back towards its original position, so the sheet must be over-bent to achieve the proper bend angle. The amount of spring back is dependent on the material, and the type of forming. When sheet metal is bent, it stretches in length. The bend deduction is the amount the sheet metal will stretch when bent as measured from the outside edges of the bend. The bend radius refers to the inside radius. The formed bend radius is dependent upon the dies used, the material properties, and the material thickness.The U-punch forms a U-shape with a single punch.		In press brake forming, a work piece is positioned over the die block and the die block presses the sheet to form a shape.Usually bend has to overcome both tensile stresses and compressive stresses. When bend is done, the residual stresses cause the material to spring back towards its original position, so the sheet must be over-bent to achieve the proper bend angle. The amount of spring back is dependent on the material, and the type of forming. When sheet metal is bent, it stretches in length. The bend deduction is the amount the sheet metal will stretch when bent as measured from the outside edges of the bend. The bend radius refers to the inside radius. The formed bend radius is dependent upon the dies used, the material properties, and the material thickness.The U-punch forms a U-shape with a single punch.
	==Types==		==Types==
	There are three basic types of bend on a press brake, each is defined by the relationship of the end tool position to the thickness of the material. These three are Air Bending, Bottoming and Coining. The configuration of the tools for these three types of bend are nearly identical. A die with a long rail form tool with a radiused tip that locates the inside profile of the bend is called a punch. Punches are usually attached to the ram of the machine by clamps and move to produce the bending force. A die with a long rail form tool that has concave or V shaped lengthwise channel that locate the outside profile of the form is called a die. Dies are usually stationary and located under the material on the bed of the machine. Note that some locations do not differentiate between the two different kinds of dies (punches and dies.) The other types of bending listed use specially designed tools or machines to perform the work.		There are three basic types of bend on a press brake, each is defined by the relationship of the end tool position to the thickness of the material. These three are Air Bending, Bottoming and Coining. The configuration of the tools for these three types of bend are nearly identical. A die with a long rail form tool with a radiused tip that locates the inside profile of the bend is called a punch. Punches are usually attached to the ram of the machine by clamps and move to produce the bending force. A die with a long rail form tool that has concave or V shaped lengthwise channel that locate the outside profile of the form is called a die. Dies are usually stationary and located under the material on the bed of the machine. Note that some locations do not differentiate between the two different kinds of dies (punches and dies.) The other types of bending listed use specially designed tools or machines to perform the work.

	===Air bend===		===Air bend===
	This bend method forms material by pressing a punch also called the upper or top die into the material, forcing it into a bottom V-die, which is mounted on the press. The punch forms the bend so that the distance between the punch and the side wall of the V is greater than the material thickness (T).Either a V-shaped or square opening may be used in the bottom die . A set of top and bottom dies are made for each product or part produced on the press. Because it requires less bend force, air bend tends to use smaller tools than other methods.		This bend method forms material by pressing a punch also called the upper or top die into the material, forcing it into a bottom V-die, which is mounted on the press. The punch forms the bend so that the distance between the punch and the side wall of the V is greater than the material thickness (T).Either a V-shaped or square opening may be used in the bottom die . A set of top and bottom dies are made for each product or part produced on the press. Because it requires less bend force, air bend tends to use smaller tools than other methods.
Line 23:		Line 19:
	Depending on material properties, the sheet may be overbended to compensate for springback.		Depending on material properties, the sheet may be overbended to compensate for springback.
	Air bend does not require the bottom tool to have the same radius as the punch. Bend radius is determined by material elasticity rather than tool shape.The flexibility and relatively low tonnage required by air bends are helping to make it a popular choice. Quality problems associated with this method are countered by angle-measuring systems, clamps and crowning systems adjustable along the x and y axes, and wear-resistant tools.The K-Factor approximations given below are more likely to be accurate for air bending than the other types of bending due to the lower forces involved in the forming process.		Air bend does not require the bottom tool to have the same radius as the punch. Bend radius is determined by material elasticity rather than tool shape.The flexibility and relatively low tonnage required by air bends are helping to make it a popular choice. Quality problems associated with this method are countered by angle-measuring systems, clamps and crowning systems adjustable along the x and y axes, and wear-resistant tools.The K-Factor approximations given below are more likely to be accurate for air bending than the other types of bending due to the lower forces involved in the forming process.

	===Bottoming===		===Bottoming===
	In bottoming, the sheet is forced against the V opening in the bottom tool. U-shaped openings cannot be used. Space is left between the sheet and the bottom of the V opening. The optimum width of the V opening is 6 T (T stands for material thickness) for sheets about 3 mm thick, up to about 12 T for 12 mm thick sheets. The bending radius must be at least 0.8 T to 2 T for sheet steel. Larger bend radius require about the same force as larger radii in air bend, however, smaller radii require greater force—up to five times as much—than air bend. Advantages of bottoming include greater accuracy and less springback. A disadvantage is that a different tool set is needed for each bend angle, sheet thickness, and material. In general, air bending is the preferred technique.		In bottoming, the sheet is forced against the V opening in the bottom tool. U-shaped openings cannot be used. Space is left between the sheet and the bottom of the V opening. The optimum width of the V opening is 6 T (T stands for material thickness) for sheets about 3 mm thick, up to about 12 T for 12 mm thick sheets. The bending radius must be at least 0.8 T to 2 T for sheet steel. Larger bend radius require about the same force as larger radii in air bend, however, smaller radii require greater force—up to five times as much—than air bend. Advantages of bottoming include greater accuracy and less springback. A disadvantage is that a different tool set is needed for each bend angle, sheet thickness, and material. In general, air bending is the preferred technique.

	===Coining===		===Coining===
	In coining, the top tool forces the material into the bottom die with 5 to 30 times the force of air bend, causing permanent deformation through the sheet. There is little, if any, springback. Coining can produce an inside radius is as low as 0.4 T, with a 5 T width of the V opening. While coining can attain high precision, higher costs mean that it is not often used.		In coining, the top tool forces the material into the bottom die with 5 to 30 times the force of air bend, causing permanent deformation through the sheet. There is little, if any, springback. Coining can produce an inside radius is as low as 0.4 T, with a 5 T width of the V opening. While coining can attain high precision, higher costs mean that it is not often used.

	===Three-point bending===		===Three-point bending===
	Three-point bending is a newer process that uses a die with an adjustable-height bottom tool, moved by a servo motor. The height can be set within 0.01 mm. Adjustments between the ram and the upper tool are made using a hydraulic cushion, which accommodates deviations in sheet thickness. Three-point bending can achieve bend angles with 0.25 deg. precision. While three-point bending permits high flexibility and precision, it also entails high costs and there are fewer tools readily available. It is being used mostly in high-value niche markets.		Three-point bending is a newer process that uses a die with an adjustable-height bottom tool, moved by a servo motor. The height can be set within 0.01 mm. Adjustments between the ram and the upper tool are made using a hydraulic cushion, which accommodates deviations in sheet thickness. Three-point bending can achieve bend angles with 0.25 deg. precision. While three-point bending permits high flexibility and precision, it also entails high costs and there are fewer tools readily available. It is being used mostly in high-value niche markets.

	===Folding===		===Folding===
	In folding, clamping beams hold the longer side of the sheet. The beam rises and folds the sheet around a bend profile. The bend beam can move the sheet up or down, permitting the fabricating of parts with positive and negative bend angles. The resulting bend angle is influenced by the folding angle of the beam, tool geometry, and material properties. Large sheets can be handled in this process, making the operation easily automated. There is little risk of surface damage to the sheet.		In folding, clamping beams hold the longer side of the sheet. The beam rises and folds the sheet around a bend profile. The bend beam can move the sheet up or down, permitting the fabricating of parts with positive and negative bend angles. The resulting bend angle is influenced by the folding angle of the beam, tool geometry, and material properties. Large sheets can be handled in this process, making the operation easily automated. There is little risk of surface damage to the sheet.

	===Wiping===		===Wiping===
	In wiping, the longest end of the sheet is clamped, then the tool moves up and down, bending the sheet around the bend profile. Though faster than folding, wiping has a higher risk of producing scratches or otherwise damaging the sheet, because the tool is moving over the sheet surface. The risk increases if sharp angles are being produced. Wiping on press brakes involves special tools.		In wiping, the longest end of the sheet is clamped, then the tool moves up and down, bending the sheet around the bend profile. Though faster than folding, wiping has a higher risk of producing scratches or otherwise damaging the sheet, because the tool is moving over the sheet surface. The risk increases if sharp angles are being produced. Wiping on press brakes involves special tools.
	This method will typically bottom or coin the material to set the edge to help overcome springback. In this bending method, the radius of the bottom die determines the final bend radius.		This method will typically bottom or coin the material to set the edge to help overcome springback. In this bending method, the radius of the bottom die determines the final bend radius.

	===Rotary bending===		===Rotary bending===
	Rotary bending is similar to wiping but the top die is made of a freely rotating cylinder with the final formed shape cut into it and a matching bottom die. On contact with the sheet, the roll contacts on two points and it rotates as the forming process bends the sheet. This bending method is typically considered a non-marking forming process suitable to pre-painted or easily marred surfaces. This bending process can produce angles greater than 90° in a single hit on standard press brakes or flat presses.		Rotary bending is similar to wiping but the top die is made of a freely rotating cylinder with the final formed shape cut into it and a matching bottom die. On contact with the sheet, the roll contacts on two points and it rotates as the forming process bends the sheet. This bending method is typically considered a non-marking forming process suitable to pre-painted or easily marred surfaces. This bending process can produce angles greater than 90° in a single hit on standard press brakes or flat presses.

	===Roll bending===		===Roll bending===
	The roll bending process induces a curve into bar or plate workpieces.		The roll bending process induces a curve into bar or plate workpieces.

	===Elastomer bending===		===Elastomer bending===
	In this method, the bottom V-die is replaced by a flat pad of urethane or rubber. As the punch forms the part, the urethane deflects and allows the material to form around the punch. This bending method has a number of advantages. The urethane will wrap the material around the punch and the end bend radius will be very close to the actual radius on the punch. It provides a non-marring bend and is suitable for pre-painted or sensitive materials. Using a special punch called a radius ruler with relieved areas on the urethane U-bends greater than 180° can be achieved in one hit, something that is not possible with conventional press tooling. Urethane tooling should be considered a consumable item and while they are not cheap, they are a fraction of the cost of dedicated steel tooling. It also has some drawbacks, this method requires tonnage similar to bottoming and coining and does not do well on flanges that are irregular in shape, that is where the edge of the bent flange is not parallel to the bend and is short enough to engage the urethane pad.		In this method, the bottom V-die is replaced by a flat pad of urethane or rubber. As the punch forms the part, the urethane deflects and allows the material to form around the punch. This bending method has a number of advantages. The urethane will wrap the material around the punch and the end bend radius will be very close to the actual radius on the punch. It provides a non-marring bend and is suitable for pre-painted or sensitive materials. Using a special punch called a radius ruler with relieved areas on the urethane U-bends greater than 180° can be achieved in one hit, something that is not possible with conventional press tooling. Urethane tooling should be considered a consumable item and while they are not cheap, they are a fraction of the cost of dedicated steel tooling. It also has some drawbacks, this method requires tonnage similar to bottoming and coining and does not do well on flanges that are irregular in shape, that is where the edge of the bent flange is not parallel to the bend and is short enough to engage the urethane pad.

	===Joggling===		===Joggling===
	Joggling,also known as joggle bending, is an offset bending process in which the two opposite bends are each less than 90° , and are separated by a neutral web so that the offset is less than 5 workpiece thicknesses.Often the offset will be one workpiece thickness, in order to allow a lap joint which is smooth on the show-face.		Joggling,also known as joggle bending, is an offset bending process in which the two opposite bends are each less than 90° , and are separated by a neutral web so that the offset is less than 5 workpiece thicknesses.Often the offset will be one workpiece thickness, in order to allow a lap joint which is smooth on the show-face.

	==Sources==		==Sources==
	[http://en.wikipedia.org/wiki/Bending_(metalworking) Wikipedia Bends]		[http://en.wikipedia.org/wiki/Bending_(metalworking) Wikipedia Bends]

Kodiyath at 09:27, 31 December 2012

2012-12-31T09:27:09Z

← Older revision		Revision as of 03:27, 31 December 2012
Line 43:		Line 43:
	Joggling,also known as joggle bending, is an offset bending process in which the two opposite bends are each less than 90° , and are separated by a neutral web so that the offset is less than 5 workpiece thicknesses.Often the offset will be one workpiece thickness, in order to allow a lap joint which is smooth on the show-face.		Joggling,also known as joggle bending, is an offset bending process in which the two opposite bends are each less than 90° , and are separated by a neutral web so that the offset is less than 5 workpiece thicknesses.Often the offset will be one workpiece thickness, in order to allow a lap joint which is smooth on the show-face.
	==Sources==		==Sources==
	[http://en.wikipedia.org/wiki/Bending_(metalworking) Wikipedia ~~Bend~~]		[http://en.wikipedia.org/wiki/Bending_(metalworking) Wikipedia Bends]

Kodiyath at 09:26, 31 December 2012

2012-12-31T09:26:18Z

Show changes

Kodiyath at 07:25, 31 December 2012

2012-12-31T07:25:48Z

@@ Line 7: / Line 7: @@
 * Please start editing this page after the /noinclude
 * -------------------------------------------------></noinclude>
-This page is still empty. If you know something about this product, please share your knowledge with others.

Admin: Created page with "Category:Piping{{Knoppen}}