5,406
edits
Difference between revisions of "Acoustic Cleaners"
Jump to navigation
Jump to search
m
no edit summary
m |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:Cleaning]]{{Knoppen}} | [[Category:Cleaning]]{{Knoppen}} | ||
[[File:Acoustic_Cleaner.jpg|thumb|right|Acoustic cleaner]] | |||
'''Acoustic Cleaners''' are used wherever there is a build-up of dry materials and particulates which need to be cleaned regularly to ensure maximum efficiency, and minimize maintenance and down time. An acoustic cleaner works by generating powerful sound waves which will vibrate the dry materials differently to each other and the surrounding structures. | '''Acoustic Cleaners''' are used wherever there is a build-up of dry materials and particulates which need to be cleaned regularly to ensure maximum efficiency, and minimize maintenance and down time. An acoustic cleaner works by generating powerful sound waves which will vibrate the dry materials differently to each other and the surrounding structures. | ||
| Line 13: | Line 7: | ||
An acoustic cleaner consists of two parts. | An acoustic cleaner consists of two parts. | ||
*The wave generator which takes the compressed air and applies it to a diaphragm. The wave generator is usually made from solid machined stainless steel. The diaphragm within the generator is the only moving part within an acoustic cleaner and there is no danger of sparking. The diaphragm is usually manufactured from special aerospace grade titanium to ensure performance and longevity. | *The wave generator which takes the compressed air and applies it to a diaphragm. The wave generator is usually made from solid machined stainless steel. The diaphragm within the generator is the only moving part within an acoustic cleaner and there is no danger of sparking. The diaphragm is usually manufactured from special aerospace grade titanium to ensure performance and longevity. | ||
*The bell, which is usually made from spun 316 grade stainless steel. The bell is a resonance section or amplifier and it will tune and direct the sound waves. An acoustic cleaner is powered by compressed air with an operating range of between 4.8 to 6.2 bars or 70 to 90 psi. The resultant sound pressure level will be around 200dB. The overall length of the acoustic cleaner will range from between 430 mm to over 3 metres long. There are generally 4 ways to control the operation of an acoustic cleaner. *The most common is by a simple timer. * | *The bell, which is usually made from spun 316 grade stainless steel. The bell is a resonance section or amplifier and it will tune and direct the sound waves. An acoustic cleaner is powered by compressed air with an operating range of between 4.8 to 6.2 bars or 70 to 90 psi. The resultant sound pressure level will be around 200dB. The overall length of the acoustic cleaner will range from between 430 mm to over 3 metres long. There are generally 4 ways to control the operation of an acoustic cleaner. | ||
*The most common is by a simple timer. | |||
*SCADA (Supervisory Control and Data Acquisition). | |||
*[[PLC Controllers]] | *[[PLC Controllers]] | ||
*Manually by [[Ball Valves]]. An acoustic cleaner will typically sound for 10 seconds and then wait for a further 500 seconds before sounding again. This ratio for on/off is approximately proportional to the working life of the diaphragm. Provided the operating environment is between – 40 and 100 °C a diaphragm should last between 3 and 5 years. The wave generator and the bell have a much longer life span and will often outlast the environment in which they operate. The older bells which were made from cast iron were susceptible to rusting in certain environments. The new bells made from 316 spun steel have no problem with rust and are ideal for sterile environments such as found in the food industry or in pharmaceutical plants. Acoustic cleaning began in the early 1970s with experiments using ship horns or air raid sirens. The first acoustic cleaners were made from cast iron. From 1990 onwards the technology became commercially viable and began to be used in dry processing, storage, transport, power generation and manufacturing industries. The latest technology uses 316 spun stainless steel to ensure optimum performance. | *Manually by [[Ball Valves]]. An acoustic cleaner will typically sound for 10 seconds and then wait for a further 500 seconds before sounding again. This ratio for on/off is approximately proportional to the working life of the diaphragm. Provided the operating environment is between – 40 and 100 °C a diaphragm should last between 3 and 5 years. The wave generator and the bell have a much longer life span and will often outlast the environment in which they operate. The older bells which were made from cast iron were susceptible to rusting in certain environments. The new bells made from 316 spun steel have no problem with rust and are ideal for sterile environments such as found in the food industry or in pharmaceutical plants. Acoustic cleaning began in the early 1970s with experiments using ship horns or air raid sirens. The first acoustic cleaners were made from cast iron. From 1990 onwards the technology became commercially viable and began to be used in dry processing, storage, transport, power generation and manufacturing industries. The latest technology uses 316 spun stainless steel to ensure optimum performance. | ||
| Line 22: | Line 18: | ||
*Sound propagation. This relates to an understanding of the nature of the sound waves, how they vary and how they will interact with the environment. | *Sound propagation. This relates to an understanding of the nature of the sound waves, how they vary and how they will interact with the environment. | ||
*Mathematics of the environment. Materials science, surface friction, distance and areas familiar to a mechanical engineer. | *Mathematics of the environment. Materials science, surface friction, distance and areas familiar to a mechanical engineer. | ||
*Chemical engineering. The chemical properties of the powder or substance to be debonded. Especially the auto adhesive properties of the powder. An acoustic cleaner will create a series of very rapid and powerful sound induced pressure fluctuations which are then transmitted into the solid particles of ash, dust, granules or powder. This causes them to move at differing speeds and debond from adjoining particles and the surface that they are adhering to. Once they have been separated then the material will fall off due to gravity or it will be carried away by the process gas or air stream. The key features which determine whether or not an acoustic cleaner will be effective for any given problem are the particle size range, the moisture content and the density of the particles as well as how these characteristics will change with temperature and time. Typically particles between 20 micrometres and 5 mm with moisture content below 8.5% are ideal. Upper temperature limits are dependent upon the melting point of the particles and acoustic cleaners have been employed at temperatures above 1000 | *Chemical engineering. The chemical properties of the powder or substance to be debonded. Especially the auto adhesive properties of the powder. An acoustic cleaner will create a series of very rapid and powerful sound induced pressure fluctuations which are then transmitted into the solid particles of ash, dust, granules or powder. This causes them to move at differing speeds and debond from adjoining particles and the surface that they are adhering to. Once they have been separated then the material will fall off due to gravity or it will be carried away by the process gas or air stream. The key features which determine whether or not an acoustic cleaner will be effective for any given problem are the particle size range, the moisture content and the density of the particles as well as how these characteristics will change with temperature and time. Typically particles between 20 micrometres and 5 mm with moisture content below 8.5% are ideal. Upper temperature limits are dependent upon the melting point of the particles and acoustic cleaners have been employed at temperatures above 1000 °C to remove ash build-up in boiler plants. It is important to match the operating frequencies to the requirements. Higher frequencies can be directed more accurately whilst lower frequencies will carry further, and are generally used for more demanding requirements. | ||
A typical selection of frequencies available would be as follows: | A typical selection of frequencies available would be as follows: | ||
*420 Hz for a small acoustic cleaner which might be used to clear bridging at the base of a silo. | *420 Hz for a small acoustic cleaner which might be used to clear bridging at the base of a silo. | ||
*350 Hz will be more powerful and this frequency can be used to unblock material build-up in ID (induced draft) fans, filters, cyclones, mixers, dryers and coolers. | *350 Hz will be more powerful and this frequency can be used to unblock material build-up in ID (induced draft) fans, [[filters]], [[cyclones]], [[mixers]], [[dryers]] and [[coolers]]. | ||
*230 Hz. At this frequency, the power involved is sufficient to use in most electricity generation applications. | *230 Hz. At this frequency, the power involved is sufficient to use in most electricity generation applications. | ||
*75 Hz and 60 Hz. These are generally the most powerful acoustic cleaners and are often used in large vessels and silos. | *75 Hz and 60 Hz. These are generally the most powerful acoustic cleaners and are often used in large [[vessels]] and [[silos]]. | ||
| Line 51: | Line 47: | ||
*Extended plant life. Aggressive cleaning regimes are avoided. | *Extended plant life. Aggressive cleaning regimes are avoided. | ||
*Ease of operation. It is easy to automate the horns either at regular intervals or to tie the sounding in to changes in their environment such as pressure or flow rates. | *Ease of operation. It is easy to automate the horns either at regular intervals or to tie the sounding in to changes in their environment such as pressure or flow rates. | ||
*Importantly they prevent the material build up problem from occurring in the first place. These advantages mean that the financial payback is often very quick. It is also possible to compare acoustic cleaners directly to alternative solutions. *Air cannons. These are well established but are expensive with limited coverage thus requiring multi unit purchase. They are also noise intrusive and have a high compressed air consumption. | *Importantly they prevent the material build up problem from occurring in the first place. These advantages mean that the financial payback is often very quick. It is also possible to compare acoustic cleaners directly to alternative solutions. | ||
*Vibrators. These are easy to fit to an empty silo but can cause structural damage as well as contributing to powder compaction. *Low friction linings. These are very quiet but are expensive to install. Also they are prone to erosion and can then contaminate the environment or product. | *Air cannons. These are well established but are expensive with limited coverage thus requiring multi unit purchase. They are also noise intrusive and have a high compressed air consumption. | ||
*Vibrators. These are easy to fit to an empty silo but can cause structural damage as well as contributing to powder compaction. | |||
*Low friction linings. These are very quiet but are expensive to install. Also they are prone to erosion and can then contaminate the environment or product. | |||
*Inflatable pads and liners. Again these are easy to install in an empty silo. They help side wall build up but have no impact on bridging. They are also hard to maintain and can cause compaction. | *Inflatable pads and liners. Again these are easy to install in an empty silo. They help side wall build up but have no impact on bridging. They are also hard to maintain and can cause compaction. | ||
*Fluidisation through a 1 way membrane. This can help already compacted material. However they are expensive and difficult to install and maintain. They can also contribute to mechanical interlocking and bridging. | *Fluidisation through a 1 way membrane. This can help already compacted material. However they are expensive and difficult to install and maintain. They can also contribute to mechanical interlocking and bridging. | ||
| Line 59: | Line 57: | ||
==Specific applications for acoustic cleaners== | ==Specific applications for acoustic cleaners== | ||
*Boilers. Cleaning of the heat transfer surfaces. | *Boilers. Cleaning of the heat transfer surfaces. | ||
*Electrostatic precipitators. Acoustic cleaners are being used for cleaning | *Electrostatic precipitators. Acoustic cleaners are being used for cleaning hoppers, turning vanes, distribution plates, collecting plates and electrode wires. | ||
*Super heaters, economisers and air heaters. | *Super heaters, economisers and air heaters. | ||
*Duct work. | *Duct work. | ||
| Line 65: | Line 63: | ||
*ID fans. Acoustic cleaning helps to provide a uniform cleaning pattern even for inaccessible parts of the fan. This maintains the balance of the fan. | *ID fans. Acoustic cleaning helps to provide a uniform cleaning pattern even for inaccessible parts of the fan. This maintains the balance of the fan. | ||
*[[Kilns]] inlet. Acoustic cleaners help to prevent particulate build up at the kiln inlet and this will minimise nose ring formation. | *[[Kilns]] inlet. Acoustic cleaners help to prevent particulate build up at the kiln inlet and this will minimise nose ring formation. | ||
*Mechanical pre Collectors. Acoustic cleaners help prevent build up around the impellers and between the tubes. *Mills. Acoustic cleaners help maintain material flow and also prevent blockages in the pre grind silos. They also help prevent material build up in the downstream separators and fans. | *Mechanical pre Collectors. Acoustic cleaners help prevent build up around the impellers and between the tubes. | ||
*[[Mills]]. Acoustic cleaners help maintain material flow and also prevent blockages in the pre grind silos. They also help prevent material build up in the downstream separators and fans. | |||
*Planetary Coolers. Acoustic cleaners help prevent bridging and ensure complete evacuation. | *Planetary Coolers. Acoustic cleaners help prevent bridging and ensure complete evacuation. | ||
*Precipitator. Acoustic cleaners help clean the turning vanes, distribution plates, collecting plates and electrode wires. They can either assist or replace the mechanical rapping systems. They also prevent particulate build up in the under hoppers which would otherwise result in opacity spiking. | *Precipitator. Acoustic cleaners help clean the turning vanes, distribution plates, collecting plates and electrode wires. They can either assist or replace the mechanical rapping systems. They also prevent particulate build up in the under hoppers which would otherwise result in opacity spiking. | ||
*Pre heaters. Used in towers, gas risers, cyclones and fans. *Ship cargo holds. Used both to clean and de aerate current loads. | *Pre heaters. Used in towers, gas risers, [[cyclones]] and fans. | ||
*[[Silos]] and [[Hoppers]]. To prevent bridging and rat holing. *Static cyclones. Acoustic cleaners will work both within the cyclone and with the associated duct work. | *Ship cargo holds. Used both to clean and de aerate current loads. | ||
*[[Silos]] and [[Hoppers]]. To prevent bridging and rat holing. | |||
*Static [[cyclones]]. Acoustic cleaners will work both within the cyclone and with the associated duct work. | |||